1: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
2: \chapter{The \D0 ~Detector for Run~II}
3: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
4:
5: This chapter describes the \D0 detector and the Tevatron upgrade at Run~II.
6: It is based on Diehl's review~\cite{physics:cdfd0}.
7: Fig.~\ref{fig-d0det} shows an elevation view of the \D0 detector.
8:
9: First in section~\ref{detector-coordinate} we define the coordinate system
10: used in \D0 detector. Section~\ref{detector-Tevatron} describes the upgrades
11: to the world's highest energy accelerator, the Tevatron, and its current status.
12: Since the tracking system and muon spectrometer are crucial to $B$ physics, emphasis will be placed on the muon detector and central tracking system in this
13: chapter.
14: Section~\ref{detector-silicon} describes the new silicon vertex system.
15: Section~\ref{detector-cft} describes the upgrades to the central fiber tracking system.
16: Section~\ref{detector-cals}
17: describes upgrades to the calorimeter systems. Section~\ref{detector-muons}
18: describes the upgrades to the muon detectors. Section~\ref{detector-trig}
19: describes the trigger systems. Section~\ref{detector-daq} describes the data acquisition system.
20:
21: \begin{figure}
22: \begin{center}
23: \epsfxsize=6 in
24: \epsfbox{ch3/d0det.eps}
25: \end{center}
26: \caption{Elevation view of the upgraded \D0~detector.}
27: \label{fig-d0det}
28: \end{figure}
29:
30: \boldmath
31: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
32: \section{The \D0 ~Coordinate System}
33: \label{detector-coordinate}
34: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
35: \unboldmath
36:
37: At \D0, the primary coordinate system has the $z$-axis
38: along the proton beam direction, and the positive $y$-axis pointing up,
39: so that $(x,y,z)$ make a right-handed Cartesian system.
40:
41: Sometimes cylindrical ($r,\phi, z$) coordinates are used,
42: as are spherical ($r,\phi, \theta$) coordinates,
43: $r$ and $\theta$, giving respectively
44: the perpendicular distance and the angle from the $z$-axis.
45: The azimuthal coordinate, $\phi$, gives the angle from the $x$-axis
46: in the $x-y$ projection.
47:
48: The angular variables are defined so that
49: $\theta=0$ is along the positive $z$-axis direction, and $\phi=\pi/2$ is parallel to
50: the positive $y$-axis.
51:
52: The rapidity $y$ is defined as
53: \begin{equation}
54: y = \frac{1}{2} \ln {\frac{E + p_z}{E - p_z}},
55: \label{eq:rapidity}
56: \end{equation}
57:
58: where $E$ is the energy, and $p_z$ is the particle momentum on the $z$-direction.
59:
60: The variable of pseudorapidity is often more convenient, which is defined as
61: \begin{equation}
62: \eta = - \ln [\tan{\frac{\theta}{2}}].
63: \label{eq:pseudorapidity}
64: \end{equation}
65:
66: In the limit that $m \ll E$ (where $m$ is the invariant mass),
67: the pseudorapidity approximates the true rapidity.
68:
69: ``Transverse" momentum ($p_T$) is also commonly used.
70: $p_T$ is the momentum vector projected onto a plane perpendicular to the
71: beam axis:
72: \begin{equation}
73: p_T = p \sin{\theta}.
74: \label{eq:pt}
75: \end{equation}
76:
77: This is particularly useful due to the fact that
78: in a high energy collision, many of the products of the collision escape down the
79: beam pipe, so the momenta along the beam of the colliding partons are unknown.
80: However, their transverse momenta are very small compared to their momenta
81: along the beam, so momentum can be considered to be conserved in the
82: transverse plane.
83:
84: %\begin{figure}[htb]
85: %\begin{center}
86: %\epsfxsize=6 in
87: %\epsfbox{ch3/tevatron.eps}
88: %\end{center}
89: %\caption{Fermilab Tavatron Collider}
90: %\label{fig-tevatron}
91: %\end{figure}
92:
93: \boldmath
94: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
95: \section{The Run~II Accelerator Upgrade}
96: \label{detector-Tevatron}
97: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
98: \unboldmath
99:
100: In Run~II, beginning in March 2001, the Tevatron
101: collides protons with antiprotons at a center-of-mass
102: energy of 1.96 TeV, which is a slightly higher energy than the 1.8 TeV available
103: in Run~I. In the first 3 years, four times the Run~I integrated luminosity has
104: been collected (by the end of August 2004).
105: We show in Fig.~\ref{fig_tevatron} a schematic of the Fermilab Tevatron Collider.
106: %Fig.~\ref{fig-tevatron} is a schematic of the Fermilab Tevatron Collider.
107:
108: In Run~II, a large advance has been made with the
109: construction of the Main Injector, a 150 GeV synchrotron, built in a
110: separate tunnel from the Tevatron. The Main Injector has replaced the function
111: of the Main Ring for antiproton production. It produces $2\times 10^{11}$
112: antiprotons per hour~\cite{holmes}, four times the rate of the old
113: Main Ring. A new permanent magnet ``Recycler Ring"~\cite{recycler} allows
114: recovery and reuse of uncollided antiprotons when the Main Injector has
115: produced enough to merit injecting a new store into the Tevatron.
116: Instantaneous luminosities in the range $5-20 \times 10^{31} {\rm cm}
117: ^{-2} {\rm s}^{-1}$
118: were available early in Run~II. Because the number of protons per
119: bunch is near the limit of the Tevatron, the number of bunches is
120: increased from Run~I's 6 bunches of protons and 6 of antiprotons to 36
121: of each species. With an instantaneous luminosity
122: of $20 \times 10^{31} {\rm cm}^{-2} {\rm s}^{-1}$, an average of 5.2 $p\bar{p}$ collisions
123: occurs each bunch crossing. Increasing the number of bunches
124: decreases the average number of collisions per bunch crossing.
125: By decreasing the bunch width as the store is depleted by collisions,
126: the luminosity can be maintained at an optimal level.
127:
128:
129: Such changes have profound implications for the detectors. Where in the
130: past, there were 3.5 microseconds between each beam crossing, in Run~II this
131: is 396 ns for 36 bunches.
132: This required all the front-end electronics from the detector
133: to be replaced with electronics capable of
134: faster response. Aside from the issues of shorter times between collisions,
135: the detector improves its ability to identify leptons,
136: energetic photons and charged particles, and particles emerging from
137: a secondary vertex (daughters of long-lived parents). Increasing the
138: collision rate by an order of magnitude also requires substantial
139: upgrades of the trigger and data acquisition systems to handle the
140: increased data flow.
141:
142: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
143: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
144:
145: \boldmath
146: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
147: \section{Silicon Microvertex Tracker (SMT)}
148: \label{detector-silicon}
149: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
150: \unboldmath
151:
152: The purposes of the silicon detectors are to identify tracks of charged
153: particles that decay before they reach the outer tracker, to reconstruct
154: the decay vertices of $b$ hadrons, and to extend or improve the track-finding
155: and momentum resolution. Because the proton and antiproton beams are very
156: thin $(\sigma_{\rm transverse}<40~\mu {\rm m})$ and because their transverse
157: positions can be
158: maintained very close to the center of the beampipe, a typical
159: $b$-hadron decay vertex can be identified by the impact parameters of the
160: tracks of $\sim$ $300~\mu {\rm m}$. This requires fine-pitched detectors oriented
161: perpendicularly to the trajectories of the charged particles and mounted
162: as close as practical to the decay vertices. The fine pitch and small radius
163: necessary to achieve sufficient impact parameter resolution also
164: improves the momentum resolution of the tracker systems.
165:
166: The accelerator parameters contribute to the design decisions.
167: The interactions are spread out over a length $\sigma_z=25$ cm,
168: setting the length scale and motivating the detectors to have
169: extended geometries.
170: The expected integrated luminosity implies a radiation dose of $\leq 1$ Mrad
171: during the life of the silicon detector. This, in turn, forces the sensors and
172: readout chips to be radiation-hard and operated at cold temperatures, which
173: mitigates some of the adverse effects of radiation.
174:
175: The basic detector design is the ``barrel geometry'' comprised of layers of
176: silicon detectors arranged in plates perpendicular to the beampipe.
177: In addition to measuring separated vertices and improving the momentum resolution,
178: D\O \ chose to use silicon detectors
179: to extend the tracking coverage to high pseudorapidity with disk-shaped
180: assemblies comprised of wedge-shaped silicon wafers arranged in plates
181: oriented perpendicular to the beamline.
182:
183: The D\O \ silicon microvertex detector~\cite{lipton}
184: consists of six barrel modules, twelve small
185: disks (``F-disks"), and four large disks (``H-disks").
186: The mixed barrel/disk geometry provides silicon sensors arrayed at normal
187: incidence, as is optimal for good tracking resolution, to charged particles
188: with $|\eta |< 3$.
189: Figure~\ref{fig-d0-silicon} shows the D\O \ silicon barrel modules with
190: barrel detectors parallel to the beamline and disks perpendicular to the
191: beamline.
192:
193: \begin{figure}
194: \begin{center}
195: \epsfxsize=4.5 in
196: \epsfbox{ch3/d0-silicon-new.eps}
197: \end{center}
198: \caption{D\O \ silicon detector. The figure shows the configuration of the 6 barrel
199: modules, the 12 ``F-disks", and the 4 ``H-disks".}
200: \label{fig-d0-silicon}
201: \end{figure}
202:
203: The six barrel modules are constructed with 4 layers of ladder assemblies
204: with considerable overlap. Each barrel module is 12.4 cm in length and the
205: total length of the barrel is 76.2 cm. The 4-layer coverage corresponds to
206: the region $\eta=1.5$ for interactions at $z=0$. Barrel layers one and three
207: are constructed from double-sided silicon sensors with axial $(r-z)$ and
208: $90^\circ$ stereo layers, except for the modules on each end of the barrel,
209: modules one and six,
210: which have single-sided axial strips. These are single-sided because
211: stereo tracking is dominated by the information from the F-disks.
212: Barrel layers two and four are constructed from double-sided detectors
213: with axial and $2^\circ$ stereo layers in all six barrel modules.
214: All of the detectors are AC-coupled to the readout electronics.
215:
216: The 12 ``F-disks" are comprised of 12 trapezoidal wedges arranged into a plate
217: with a hole for the beampipe. The active area inner radius is at 2.5 cm
218: from the center of the beampipe and the outer is at 9.8 cm.
219: The detectors are AC-coupled, double-sided, with strips angled
220: at $\pm 15^\circ$ with respect to the vertical. The pitch of the p-side and
221: n-side detectors is $50~\mu {\rm m}$ and $62.5~\mu {\rm m}$, respectively,
222: and the silicon wafers are 300~$\mu {\rm m}$ thick. Naturally, the strips are
223: of different length depending on their locations
224: on the wedge. The six innermost F-disks attached to the outer sides of the
225: six barrel modules. The three additional F-disks are attached to each
226: outer side of the barrel assembly, with the effect of extending the acceptance
227: of the silicon system to higher pseudorapidity, especially for interactions
228: which occur at larger $z$.
229:
230: The four large ``H-disks" are located at $z=\pm 94$ cm and $z=\pm 126$ cm.
231: The inner radius of the active area is at 9.6 cm from the center of the
232: beampipe and the outer is at 23.6 cm. The detectors are AC-coupled,
233: single-sided, with 40 $\mu {\rm m}$ pitch strips
234: (pairwise readout makes the effective pitch 80 $\mu {\rm m}$)
235: angled at $\pm 7.5^\circ$
236: from the vertical. Each plane has wedges glued together back-to-back to
237: provide a $15^\circ$ stereo angle. These forward disks are necessary to
238: provide track stubs for forward particles which would otherwise exit the
239: region of full solenoidal magnetic field without hitting the outer tracker.
240: They cover a pseudorapidity range of approximately $2\le |\eta| \le 3$.
241:
242: All of the three detector types are able to withstand a radiation dose
243: greater than 1 Mrad. The dose depends on the detector location and integrated
244: luminosity. The innermost layer is expected to receive 0.5 Mrad/fb$^{-1}$.
245: The effect of the radiation damage is to increase the leakage current,
246: increase the bias voltage necessary for full depletion, and decrease the
247: signal-to-noise ratio. The effects are temperature dependent and can be
248: reduced by operated the detectors at low temperatures. The detectors
249: are operated at temperatures between $5-10^\circ$ C using a cooling
250: mixture of deionized ethylene glycol and water.
251:
252: The D\O \ silicon detectors are read out using the SVX~II
253: chip~\cite{FNALTM1892}. SVX~II is a 128 channel, radiation hard CMOS chip
254: mounted directly on the ``High Density Interconnects" (HDI's), kapton-based
255: flexible circuit, wire-bonded to the sensors at the ends of the ladders
256: and wedges. Each of the 128 channels in an SVX~II chip features a
257: preamplifier, a 32 stage analog pipeline with 4 $\mu {\rm s}$ delay,
258: an 8-bit Wilkinson type ADC, and a latch-based sparsified readout.
259: The chip is programmable for any interaction time from 132 to 396 ns.
260: The pipeline depth, ADC ramp rate, preamplifier bandwidth, and thresholds
261: are downloadable to each SVX~II chip.
262:
263: Connections to the outside world continue from the HDI's to 8-ft
264: long ``low-mass" cables that join the ends of the HDI's to unpowered
265: ``transition cards" mounted on the ends of the central calorimeter
266: cryostat. Ultimately, these signals are gathered by a sequencer board
267: connected by optical link to VME readout buffer electronics in the movable
268: counting house. The D\O \ silicon detector has 792,576 channels.
269:
270: \boldmath
271: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
272: \section{Outer Tracker: Central Scintillating Fiber Tracker (CFT)}
273: \label{detector-cft}
274: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
275: \unboldmath
276:
277: The outer tracker~\cite{physics:cdfd0} is the charged particle tracker at largest radius
278: within the calorimeter. Outer trackers perform two functions. The
279: first is measuring the momentum and charge of particles
280: produced in the collision, and the second is to provide
281: pattern recognition assistance for the silicon detectors.
282:
283: A particle with non-zero charge $q$ and momentum $p$ in a
284: solenoidal magnetic field along the $z$-direction
285: of strength $B$ will travel in a helix with radius $r$
286: given by
287:
288: \begin{equation}
289: r = \frac{p_T}{qB},
290: \end{equation}
291:
292: where $p_T = \sqrt{p_x^2 + p_y^2}$. Therefore, by measuring
293: the track's curvature in the $r-\phi$ plane, we
294: effectively measure $p_T$. By measuring the
295: track's direction in the $r-z$ plane, we measure
296: $p_T/p_z$, which completes our measurement of the
297: 3D momentum vector of the particle.
298:
299: Tracks in these detectors typically have several
300: dozen hits, which allows for highly efficient
301: and pure identification of these tracks. Silicon
302: trackers in these detectors have of order a
303: half-dozen hits, and while they can be used
304: standalone, a much better way to use them is to
305: find the track in the outer tracker and project
306: this track back into the silicon. Once the
307: approximate trajectory in the silicon detector
308: has been established, the tracking algorithm
309: can search the silicon detector for hits and
310: use these hits to improve the track measurement.
311: This technique uses each component to its best
312: advantage: the silicon tracker measures the
313: track's point of origin and initial direction,
314: and the outer tracker measures the track's
315: momentum.
316:
317:
318: \subsubsection{The D\O \ Solenoid and Scintillating Fiber Tracker}
319:
320: One substantial improvement to the D\O \ detector for Run~II was
321: the addition of a superconducting solenoidal magnet providing a solenoidal field of 2T parallel to the $z$-axis.
322: Having a magnetic field enhances the D\O \ detector.
323: It has the ability to measure the momentum and charge of leptons and hadrons.
324: The muon momentum can be measured in the central magnetic field,
325: before the muon has scattered in the steel of the muon toroids,
326: and this allows for the comparison of the muon's momentum as measured in the solenoid to the
327: momentum as measured in the toroids. We can see that the muon
328: momentum resolution is much improved after matching a
329: muon local track with central track.
330:
331: Mechanically, the D\O \ outer tracker is a
332: simple device. Layers of scintillating fiber
333: are placed on carbon-fiber composite cylinders.
334: When a particle travels through one of these
335: fibers, the scintillator emits light, which is
336: totally internally reflected down the fiber,
337: coupled to a clear fiber, and transported
338: to a solid-state light detector. Fig.~\ref{fig-d0-tracker}
339: shows a side view of the tracker.
340:
341:
342: \begin{figure}
343: \begin{center}
344: \epsfxsize=4.5 in
345: \epsfbox{ch3/d0-tracker.eps}
346: \end{center}
347: \caption{D\O 's scintillating fiber tracker.}
348: \label{fig-d0-tracker}
349: \end{figure}
350:
351: In detail, the D\O \ central fiber tracker (CFT)~\cite{wayne} consists of
352: scintillating fibers mounted on eight concentric cylinders made from
353: a composite of layers of high modulus of elasticity carbon fiber
354: sandwiching structural foam. The cylinders range in radius from 20 to 50 cm
355: and are about 2.5 m in length, except for the inner two,
356: which are about 1.7 m in length. The scintillating fibers are
357: double clad, 835~$\mu$m in diameter, and
358: are constructed in ribbons each 128 fibers wide composed of
359: a ``doublet" layer of fibers with the centers of one of the single layers
360: in the space between the fibers of the other single
361: layer. There are eight doublet axial (aligned along the beam
362: axis) layers of scintillating fiber, as well as eight doublet stereo
363: layers that make a $\pm 3^{\circ}$ angle with the beam axis.
364: The outer (8th) layer is at the largest possible radius.
365: The 7th layer is as close to the outer layer as is possible. The
366: inner layer is at the least possible radius.
367: The detector is divided into 80 sectors in $\phi$. Each pie-shaped
368: slice has 960 fibers and the entire detector therefore
369: has 76,800 channels.
370:
371: The scintillation light from the fibers is totally internally
372: reflected down the length of the fiber. A connection is made at the
373: edge of the tracker to a clear fiber that transports the light to a
374: solid-state light detector called a Visible Light Photon Counter (VLPC).
375: The number of photons available at the VLPC's,
376: for a charged particle which traverses through the center of a fiber,
377: varies from 10 to 40, depending on the charged particle's pseudorapidity
378: and on attenuation due to the distance from the clear fiber connector.
379: The VLPC's are small silicon devices which
380: have an array of eight photo sensitive areas, each 1 mm in diameter,
381: on their surface. They operate at temperatures from 6 to 15 K,
382: have a quantum efficiency of over 80\%, and have a gain of
383: 20,000 to 50,000. The high quantum efficiency is important
384: because of the low number of photons.
385:
386: The momentum resolution is currently $\sigma(p_T)/p_T=0.13\% \cdot p_T$
387: when scintillating fiber tracker measurements are combined with the silicon tracker.
388: The $p_T$-dependent impact parameter resolution is currently 30~$\mu {\rm m}$ in the $x$ and $y$ direction, and 42~$\mu {\rm m}$ in the $z$ direction
389: for high momentum tracks, if SMT and CFT information are combined.
390:
391: %======================================================
392: %======================================================
393:
394: \boldmath
395: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
396: \section{Calorimeters and Preshower Detectors}
397: \label{detector-cals}
398: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
399: \unboldmath
400:
401: Because of the dependence of the Tevatron's physics program
402: on lepton identification and jet energy measurement,
403: calorimetry is a critical aspect of Run II experiments.
404: The calorimeters are used for identification and measurement of the
405: electron, neutrino and jets from the decays of the top
406: quarks in these events.
407:
408: The calorimetry is divided into two parts, electromagnetic
409: and hadronic. Nearest the vertex is the electromagnetic
410: calorimeter that measures the energy of electrons and photons
411: (including those from $\pi^0$ and $\eta$ decay) and has
412: improved position measurement at the point of maximum
413: shower development. Farther in radius is the hadronic
414: calorimeter which measures the energy of hadrons as
415: they interact with the material of the calorimeter.
416: Muons deposit a small amount of energy (due to ionization)
417: in both sections, and the lack of a large energy deposit
418: can be used to identify a particle as a muon. Neutrinos
419: deposit no energy at all in these calorimeters, but
420: the absence of energy deposition appears as a momentum
421: imbalance in the transverse plane, also called ``missing
422: $E_T$".
423:
424: D\O's hermetic, radiation-hard uranium and liquid-argon
425: calorimeter~\cite{d0runI} consists of three separate cryostats: the Central
426: Calorimeter (CC), and the two Endcap Calorimeters (EC's). Each is segmented
427: into an electromagnetic section, a hadronic section, and a coarse hadronic
428: section (inside to outside), with many layers of sampling. Each is
429: divided into pseudoprojective towers covering $\eta \times \phi = 0.1
430: \times 0.1$ rad. The readout of the electromagnetic section has four layers of
431: longitudinal segmentation. The third electromagnetic layer,
432: at EM shower maximum, has segmentation $\eta \times \phi = 0.05 \times 0.05$ rad.
433: The readout of the hadronic sections have 4 (5) longitudinal layers in the
434: CC (EC's). There are no projective cracks.
435: The calorimeter provides hermetic coverage to $|\eta|<4$.
436: The energy resolution is $\sigma_E/E=15\%/\sqrt{E (GeV)} \oplus 0.4\%$
437: for electrons and photons. For charged pions and
438: jets the resolutions are approximately $50\%/\sqrt{E (GeV)}$ and
439: $80\%/\sqrt{E (GeV)}$, respectively.
440:
441: The Inter Cryostat Detectors (ICD's) augment the \D0 liquid argon
442: calorimeters by providing a measurement of the energy in between the
443: central and endcap cryostats. This improves the energy measurement for
444: jets that straddle the intercryostat region and improves the resolution
445: of the missing transverse energy measurement.
446: Sixteen new ICD detector segments
447: form an annular ring of 1/2" thick scintillator covering
448: $1.1\le |\eta| \le 1.4$ on the hadronic section of the inner end of each
449: EC cryostat. The sixteen segments are further segmented into sections of size
450: $\Delta \eta \times \Delta \phi =0.1 \times 0.1$.
451: Each section has an embedded wavelength shifting fiber
452: to collect light. These are in turn connected to long clear fibers which carry
453: the light to photomultiplier tubes located underneath the cryostats, in a
454: region with reduced magnetic field from the solenoid.
455:
456: The primary purpose of the Central and Forward Preshower Detectors (CPS and FPS)
457: is to exploit the difference
458: between energy loss mechanisms of electrons and photons with that of the
459: backgrounds, principally hadronic jets with leading $\pi^0$'s, to improve
460: the trigger and offline purity. Secondly, they provide a precision
461: measurement of the starting point of the electromagnetic showers.
462: The CPS is cylindrically shaped, mounted on the outside of the solenoid
463: magnet, and covers the region $|\eta|\le 1.3$. The FPS are shaped like
464: annular rings, mounted on the inside of the EC's, and cover the region
465: $1.5\le|\eta|\le 2.5$. The FPS and CPS are shown in Fig.~\ref{fig-d0-fps3}.
466:
467: The D\O \ Run~II luminosity monitor (Level-0) consists of two
468: arrays of plastic scintillation counters located on the inside faces
469: of the EC's and arranged symmetrically around the beampipe.
470: The pseudorapidity coverage is $2.7 \le |\eta| \le 4.4$. Because the
471: solenoid field is $\sim 1$~Tesla in that region, short magnetic field
472: resistant photomultiplier tubes are used to read the light. A coincidence
473: of hits in the counters on both sides of the interaction point
474: provides the simplest indication that an inelastic collision occurred.
475:
476: A new near beam detector called the ``Forward Proton Detector (FPD)" is available
477: for Run~II. It is a series of small, retractable scintillating fiber
478: detectors placed a few millimeters from the beamline in the region 20--60
479: meters from both sides of the interaction point. They are triggered by
480: small scintillation counters and read out by multi-anode PMT's. Their
481: purpose is to identify scattered protons and anti-protons in diffractive
482: events.
483:
484: \begin{figure}[htbp]
485: \begin{center}
486: \epsfxsize=5.5 in
487: \epsfbox{ch3/d0-fps3.eps}
488: \end{center}
489: \caption{One quarter $r-z$ view of the end of the \D0 \ trackers
490: and the start of the EC, indicating the Central Preshower, the Level-0
491: detector, the solenoid magnet and calorimeter cryostats, and the Forward
492: Preshower detector. The Forward Preshower detector is shown in detail
493: in the inset. }
494: \label{fig-d0-fps3}
495: \end{figure}
496:
497:
498: %======================================================
499: %======================================================
500:
501: \boldmath
502: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
503: \section{Muon Systems}
504: \label{detector-muons}
505: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
506: \unboldmath
507:
508: The muon detection strategy at \D0 relies on the
509: penetration power of muons. Several meters of absorber (including
510: the calorimeters) absorbs the vast majority of hadrons, and any
511: charged particle that penetrates this material is inferred to be
512: a muon. Because they are at large radius, muon detectors are large,
513: and to keep costs reasonable, they have very coarse granularity:
514: typically they are single wire proportional chambers with drift
515: times in excess of a microsecond.
516: Fig.~\ref{fig-d0-muon-1}, and ~\ref{fig-d0-muon-2} show an $r-z$ view of the \D0 detector,
517: and all components are illustrated in the graph.
518:
519:
520: \begin{figure}[htbp]
521: \begin{center}
522: \epsfxsize=6.0 in
523: \epsfbox{ch3/muon-det-01.eps}
524: \end{center}
525: \caption{Half $r-z$ view of the \D0 \ muon subdetector.}
526: \label{fig-d0-muon-1}
527: \end{figure}
528:
529: \begin{figure}[htbp]
530: \begin{center}
531: \epsfxsize=5.0 in
532: \epsfbox{ch3/muon-det-02.eps}
533: \end{center}
534: \caption{Illustration of the \D0 \ muon subdetector components.}
535: \label{fig-d0-muon-2}
536: \end{figure}
537:
538: The muon detector consist of scintillator and drift tubes, with effectively
539: complete coverage out to $|\eta| < 2$. As seen in the layout,
540: the detector is split at $|\eta|$ of 1 into a central and forward system.
541: Each has 3 layers (usually called A,B,C with A between the calorimeter
542: and iron and the other two outside the iron) of drift tubes.
543: In the central region are proportional drift chambers (called PDTs).
544: In the forward region are minidrift tubes (called MDTs).
545: Figure~\ref{fig-MuDrift} shows the layout of PDTs and MDTs.
546:
547: %\begin{figure}
548: %\begin{center}
549: %\epsfxsize=7.0 in
550: %\epsfbox{ch3/MuDrift.eps}
551: %\end{center}
552: %\caption{Layout of PDTs and MDTs.}
553: %\label{fig-MuDrift}
554: %\end{figure}
555: \begin{figure}
556: \begin{center}
557: \includegraphics[height=15.0cm,width=160mm]{ch3/MuDrift.eps}
558: \caption{Layout of PDTs and MDTs.}
559: \label{fig-MuDrift}
560: \end{center}
561: \end{figure}
562: In Run~II, scintillator counters are added adjacent to the chambers.
563: Scintillator has a response time measured in nanoseconds, so that the
564: coincidence between the counter and the chamber unambiguously
565: determines the bunch crossing. Because the timing resolution
566: is substantially better than the minimum required to resolve
567: bunch crossings, we gain the ability to use timing to reject
568: certain backgrounds: particularly out of time particles
569: produced upstream of the interaction point and cosmic rays.
570:
571: There is 2 or 3 layers of scintillator coverage with the forward
572: scintillators sometimes called pixels, the central A-layer counters
573: called A-phi, and the BC counters called the cosmic cap. Scintillator time
574: is read out with both a 15--20 ns ``trigger'' gate and a 80--100 ns
575: ``readout'' gate.
576: The D\O \ detector relies on layers of scintillation counters and drift
577: chambers to identify muons and measure their position and momentum.
578:
579: The muon system has three large toroid magnets, one central and
580: two forward, which act as absorber in addition to the calorimeter,
581: provide a structure on which to mount the muon detectors, and provide
582: a bend to the muons so the detectors can measure the momentum.
583: The calorimeters contain between 7 and 10 interaction lengths of material,
584: depending on the pseudorapidity. The thickness of the calorimeters
585: plus the toroid magnets varies between 13 to 14 interaction lengths for
586: $|\eta|\le 0.9$, 10 to 15 interaction lengths for $0.9 \le |\eta| \le 1.2$,
587: and 18 to 20 interaction lengths for $1.2 \le |\eta| \le 2.0$. Muons
588: with momentum greater than $\sim 1.4$ GeV/$c$ ($\sim 3.5$ GeV/$c$) penetrate
589: the calorimeter (toroid magnet) at $\eta=0$.
590: In addition, new massive shielding structures isolate the muon detectors
591: from backgrounds generated near the beampipe and accelerator elements.
592:
593: \subsection{Central Muon System Drift Chambers}
594: The central muon drift chambers were retained from Run~I, but their electronics
595: have been replaced. The drift chambers are made from extruded aluminum cells
596: of 4-inch width and lengths up to 228 inches. The wires in the cells
597: are parallel to the field in the toroid magnets so that the bending of the
598: track in the toroids takes place in the drift ordinate.
599: Refer to Fig.~\ref{fig-d0-muon-1},~\ref{fig-d0-muon-2}.
600:
601: Individual drift chambers (PDT's) in the C- and B-layers consist of three
602: staggered decks of up to 24 cells each. Drift chambers in the A-layer consist
603: of four staggered decks of 24 cells each, except for the ones on the bottom,
604: which are three deck PDT's. The top and bottom of each cell has a copper-clad
605: cathode pad. The copper has a milled cut separating it into an inner and
606: outer pad such that the width of the inner pad alternately increases and
607: decreases along its length. The wavelength of the vernier is 24 inches.
608: Pairs of wires are connected through a delay chip at the end away from the
609: front-end electronics. Fig.~\ref{fig-pdt-cell} shows the geometry of a PDT cell.
610:
611: \begin{figure}[htbp]
612: \begin{center}
613: \epsfxsize=4.5 in
614: \epsfbox{ch3/pdt-cell.eps}
615: \end{center}
616: \caption{Geometry of a PDT cell.}
617: \label{fig-pdt-cell}
618: \end{figure}
619:
620: On passing through a cell, a muon will cause a
621: hit in the cell and a hit in the neighbor cell which is some time later
622: depending on the muon's proximity to the far end. Charge is accumulated on
623: the inner and outer pads of the cell through which the muon passed. The drift
624: time is derived from the sum of the two cells times. The distance along
625: the wire is derived from the difference. The normalized difference of the
626: integrated pad charge provides the distance along a pad wavelength.
627:
628: The Run~I A-layer PDT's were rebuilt so as to increase their effective
629: lifetimes. The ends of the PDT's were removed. The cathode pads, which
630: outgassed a dielectric that coated the anode wires in Run~I, were replaced
631: with new G-10 pads that do not outgas. The lifetime of the B- and C-layer PDT's
632: is long enough so that aging won't pose a problem for these detectors.
633:
634: The PDT's use a drift gas composed of 80\% argon, 10\% CF$_4$, and
635: 10\% CH$_4$. The maximum drift time is approximately 500 ns, longer
636: than the bunch spacing. This poses no problem for the electronics, which
637: records each hit in as many crossings in that it could have occurred.
638: The time measurements are made in 1.8 ns bins. The drift ordinate resolution
639: is $\sim 500~\mu {\rm m}$ per hit, limited by the fluctuations in the drift
640: time due to the gas. Normally the drift velocity is about 0.1 mm/ns.
641:
642: The muon momentum is calculated from the bend in the toroid magnet as
643: determined from the difference in slopes between the line formed from the
644: interaction point and the A-layer hits and the line through the B- and
645: C-layer hits. The momentum resolution is expected to be
646: $\sigma(1/p)=0.18/p \otimes 0.005$ with $p$ in GeV/$c$. This momentum resolution
647: is worse than that expected from the fiber tracker measurement, especially
648: at low $p_T$.
649:
650: \subsection{Central Muon System Scintillation Counters}
651: An important part of the upgrade is two new layers of scintillation counters.
652: These detectors not only tag the bunch crossing from which the muons originate
653: for the slow drift chambers, but also reject background particles which leave
654: hits at times other than expected from a muon originating at the interaction
655: point. Refer to Fig.~\ref{fig-d0-muon-1},~\ref{fig-d0-muon-2}.
656:
657: The A-layer contains 630 ``A-phi" counters, each approximately 32" long
658: and spanning $4.5^\circ$ in azimuthal angle. There are 9 counters in a row
659: spanning $-1.0 \le \eta \le 1.0$. Each row has a slight overlap with a
660: neighboring row so as to minimize the cracks between counters. The counters
661: are made from 1/2 inch thick Bicron scintillator plates with many Bicron
662: BCF'92 wavelength shifting fibers
663: embedded in deep grooves. The fibers collect and transmit the light to a
664: single photomultiplier tube (PMT).
665: %The counters are encased in light-tight
666: %aluminum boxes. The PMT's are encased in light-tight magnetic shields.
667: The counters have a time resolution of $\sigma = 4$ ns and are expected to
668: discriminate between muons produced in the collisions and the background,
669: that is composed of particles backscattered from the calorimeter exit, and
670: arrives 14 ns later than a muon.
671: The ``A-phi" counters span 93\% of the azimuthal angle. There is a gap
672: in the A-layer coverage where the calorimeter is supported by the detector
673: platform.
674:
675: A layer of scintillation counters has been added on the outside of the
676: muon toroid magnet. The 240 ``Cosmic Cap" C-layer scintillation counters
677: were deployed late in the second half of
678: Run~I and previously have been described in
679: detail~\cite{d0scintnim}. These counters are between 81.5 and 113 inches
680: long and 25 inches wide. Eight of them are mounted on the outside of each
681: C-layer PDT on the top and sides of the central muon detector.
682: Underneath the toroid magnet, the three layer coverage is broken up because
683: of the support structure for the central platform and toroid magnets.
684: 120 new ``Cosmic Bottom" counters are arrayed on bottom C-layer and
685: B-layer PDT's.
686: The Cosmic Cap and Cosmic Bottom counters are made from 1/2 inch thick
687: Bicron scintillator with Bicron BCF'91A wavelength shifter fibers embedded
688: in grooves. Each counter is read out with two photomultiplier tubes.
689: One advantage of using two PMT's is that coincidental tube noise is
690: improbable. Another is the immediate redundancy available in case one
691: of the PMT's fails.
692:
693: The scintillation counters have an LED pulser calibration system capable
694: of providing a clocked, timed, amplitude-controlled photon pulse. Each PMT
695: is connected by a light-shielded optical fiber to a light-tight box which
696: houses bundles of LED's glued into a clear acrylic block. A single box
697: may provide the photon pulse for up to 100 PMT's. The stability of the
698: photon pulse is monitored with a light-sensitive diode housed in the
699: clear block. This system allows the timing and amplitude to be
700: monitored and controlled.
701:
702: The muon system has a wide range of options available for triggering.
703: Triggers may be composed of coincidences of in-time hits in scintillation
704: counters, hits in layers of the PDT's, and tracks found in the central
705: tracker. Low-$p_T$ muons would rely on hits only in the A-layer detectors
706: and fiber tracker. High-$p_T$ muons would also use scintillation counters
707: and PDT's in the B- and C-layers.
708:
709: \subsection{Forward Muon System Drift Tubes}
710:
711: \begin{figure}[htbp]
712: \begin{center}
713: \epsfxsize=4.0 in
714: \epsfbox{ch3/d0-mdt.eps}
715: \end{center}
716: \caption{\D0~forward muon mini-drift tube (MDT) plane. The octant
717: boundaries are shown.}
718: \label{fig-d0-mdt}
719: \end{figure}
720:
721:
722: The Mini-Drift Tube (MDT) system~\cite{abramov}
723: is comprised of three planes of drift-tubes, with one plane in front of, and
724: two planes behind the forward toroid magnet.
725: The layers are divided into octants with
726: tubes of different length depending on position in the octant.
727: As in the central region, the MDT A-layer has four decks of drift tubes and
728: the B and C-layers have three decks each. The drift tubes, made from long
729: aluminum extrusions of eight 1 cm square cells, are contained in plastic
730: sleeves. Wires in the cells are oriented parallel to the magnetic field
731: of the forward toroid magnet. The sleeves of tubes are mounted on an
732: aluminum support structure which also provides mechanical support for the
733: infrastructure. A plane of MDT counters is shown in Fig.~\ref{fig-d0-mdt}.
734:
735: \begin{figure}[ht]
736: \begin{center}
737: \epsfxsize=4.5 in
738: \epsfbox{ch3/d0-mupixels.eps}
739: \end{center}
740: \caption{Two D\O \ forward muon pixel octants.}
741: \label{fig-d0-mupixels}
742: \end{figure}
743:
744:
745: The MDT's use a non-flammable gas mixture composed of 90\% CF$_4$ and
746: 10\% CH$_4$, with a maximum drift time of about 60 ns. The momentum
747: resolution is limited by multiple Coulomb scattering in the iron toroid
748: and the hit resolution of the detector. The MDT electronics uses a coarse
749: digitization of the drift time (18.8 ns time bin). The momentum resolution
750: is roughly $\sigma(p_T)/p_T = 0.2 $. Importantly, it is on par with the
751: resolution of D\O 's central tracker in the forward region where the full
752: coverage of the fiber tracker's layers has ended.
753:
754: \subsection{Forward Muon System Scintillation Counters}
755: Three layers of ``Pixel" scintillation counters~\cite{abramov}
756: are added to the forward region (approximately $1.0 \le |\eta| \le 2.0$).
757: Their primary role is muon triggering. The $\sim 4800$ pixel counters
758: have segmentation $0.1 \times 4.5^\circ$ in $\Delta \eta \times \Delta \phi$.
759: Most of the trapezoidal shaped pixel counters are made from 0.5" thick Bicron
760: scintillator with wavelength shifting bars. They are each read out by a
761: single PMT. The counters are held in protective aluminum containers with a
762: steel fastener, on one corner, which mates to the magnetic shield of the PMT.
763: A few of the counters have special space constraints and are made with
764: wavelength shifting fiber so as to allow more flexibility in the orientation
765: of the PMT and magnetic shield. The same kind of LED pulser calibration
766: system used in the central muon scintillators is used for the Pixel counters.
767:
768: The counters are assembled into octants of $\sim 100$ counters each.
769: The octants provide mechanical support for the counters and their
770: infrastructure. These are mounted directly onto the A- and
771: B-layer sides of the forward toroid magnets and onto the inside face of the
772: C-layer support frame. Two octants are shown in Fig.~\ref{fig-d0-mupixels}.
773:
774: Forward muon triggers are formed from coincidences in the three layers of
775: scintillation counters consistent with a muon of a given momentum. The
776: MDT's provide a $p_T$ measurement at trigger level, especially important
777: in the fiducial region where the fiber tracker has reduced coverage.
778:
779: \subsection{Shielding}
780: The purpose of shielding is to shield the muon detectors from backgrounds
781: generated at high $|\eta|$ from the interaction
782: of the beam jets with forward elements of the detector and accelerator
783: hardware, such as the beampipe and low-beta quadrupole magnet.
784: The shielding is built in several large, movable sections extending from the
785: endcap calorimeters, through the forward toroid magnets, to the Tevatron
786: tunnels. The shields themselves totally contain the accelerator elements
787: within the collision hall, including the low-beta quadrupole magnet, inside
788: a case of 20 inches of iron, six inches of polyethylene, and two inches of
789: lead. The shielding is shown in Figs.~\ref{fig-d0-muon-1},~\ref{fig-d0-muon-2}.
790:
791: %======================================================
792: %======================================================
793:
794: \boldmath
795: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
796: \section{Trigger}
797: \label{detector-trig}
798: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
799: \unboldmath
800:
801: One of the defining features of hadron collider physics is the
802: necessity to select the small fraction of all bunch crossings containing
803: interesting collisions.
804: A fast selection process, called the ``trigger", sorts events into
805: categories of various levels of interest.
806: An event that passes the trigger is written to magnetic tape for later
807: analysis. An event that fails the trigger is lost forever.
808: An event can fail to pass the trigger because the collision was a well
809: understood process, because the event was mistaken for a well understood
810: process (trigger inefficiency), or because the trigger or data acquisition
811: were busy processing previous collisions (dead time).
812:
813: There are three trigger levels. After Level-1 trigger, the event rate
814: is reduced from 7 MHz to 10 KHz. Level-2 trigger reduces the event rate
815: 10 times more. We can further reduce the event rate 20 times by the
816: Level-3 software trigger. After Level-3, 50 events are written to tape
817: per second.
818:
819: \subsection{Trigger Level-1}
820: The first element of the trigger is the formation of
821: trigger primitives. These are collections of a few
822: bits of data that represent the status of various detector
823: elements. For example, one set of trigger primitives are
824: the calorimeter cells with energy above a particular threshold.
825: Another would be which muon chambers have detected a particle,
826: and whether this particle is consistent with a high $p_T$
827: muon, a low $p_T$ muon, or neither. Another would be
828: the number and position of tracks found in the outer tracker (silicon
829: is not in the trigger at this stage).
830:
831: A limited amount of processing is then applied to these trigger
832: primitives. Typically, this is performed in Field Programmable Gate
833: Arrays (FPGA's) with inputs from the front-end detector electronics.
834: In D\O, for instance, Level-1 muon primitives are formed from combinations
835: of in-time hits in scintillation counters, coincidences of hit cells
836: in the drift chambers, and tracks formed from hit patterns in the
837: axial scintillating fibers of the central tracker.
838:
839: The primitives are sent to the global Level-1 trigger. Combinations
840: of trigger primitives are compared against a runtime programmable
841: list containing the definitions of triggers to be used in the run.
842: The D\O \ Level-1 trigger system can support up to 128 different unique
843: triggers.
844: If the trigger primitives satisfy at least one of the triggers, the
845: event is passed to the next trigger level.
846: A block diagram of D\O's trigger is shown in Fig.~\ref{fig-d0trigger}.
847:
848: \begin{figure}[htbp]
849: \begin{center}
850: \epsfxsize=5.0 in
851: \epsfbox{ch3/d0trigger.eps}
852: \end{center}
853: \caption{Design of the D\O \ trigger system.}
854: \label{fig-d0trigger}
855: \end{figure}
856:
857: It takes time to form the primitives and to make a Level-1 trigger
858: decision. Meanwhile collisions continue to occur. Since the trigger
859: needs to be ready for the next crossing while it is processing
860: an event, the data from the detectors is placed in a pipeline (a
861: microprocessor's ``assembly line'' for executing program instructions;
862: a pipelined function unit in a processor separates the execution
863: of an instruction into multiple stages)
864: which increments every crossing.
865:
866: The D\O \ Level-1 trigger has a
867: deadtimeless output rate of 10~kHz. If any single one of the 128 combinations is
868: positive, and the DAQ system is ready for acquisition, then the Level-1 framework
869: issues an accept, and the event data is digitized and moved into a series of
870: 16 event buffers to await a Level-2 trigger decision.
871:
872: The central Level-1 trigger logic is performed locally in the detector
873: octants.
874: A muon low ${\it p_T}$ trigger is defined using only centroids found in the A-layer,
875: while a high ${\it p_T}$ trigger is defined by
876: using correlations between centroids found in the A-layer and B- or C-layer.
877: Four thresholds (2, 4, 7 and 11 GeV/$c$) are defined using the CFT information.
878: The information for each octant in each region is combined in the muon trigger
879: manager, which produces global muon trigger information. The muon trigger
880: manager makes a trigger decision based on the ${\it p_T}$ threshold (2, 4, 7 and 11 GeV/$c$),
881: pseudorapidity region ($ |\eta|<1.0, |\eta|<1.5$ and $|\eta|<2.0$), quality (Loose,
882: Medium and Tight) and multiplicity information. This trigger decision is sent
883: to the Level-1 Trigger Framework where it is included in the global physics trigger
884: decision.
885:
886:
887:
888: \subsection{Trigger Level-2}
889:
890: At Level-2, the Level-1 decision is confirmed, or not, using
891: the additional time to provide more and better information.
892: This is done in two stages. The first stage, called the
893: preprocessor stage, uses FPGA's to refine the trigger primitives found
894: by Level-1 and to prepare the data for the second stage.
895: The second stage, called the global processor stage, combines and correlates
896: information from the trigger primitives.
897:
898: The preprocessor FPGA's have about 50 $\mu$s to perform refinements to the
899: trigger primitives. For example, the first stage photon primitive,
900: formed from a single tower at Level-1, is required to have a shape
901: that looks like an isolated electromagnetic shower at Level-2. The
902: additional time is used to compare the energy of the tower of interest
903: with nearby towers. Additional related information can also be used,
904: such as energy in the shower maximum. Because of the increased accuracy
905: of the measurement, thresholds can be set tighter in Level-2,
906: producing a great deal of the rejection in the global processor stage.
907:
908: The global processor stage for \D0 is a VME-based CPU card
909: using a Digital Alpha processor.
910: Using a general purpose CPU at this level of the trigger
911: provides a great deal of flexibility -- essentially
912: all of the Level-1 primitives are available at Level-2,
913: where they can be combined in ways not possible
914: at Level-1. For instance, Level-1 can produce
915: photon triggers and it can produce jet triggers.
916: However, Level-2 provides the ability to correlate
917: the two in ways not possible by the dedicated hardware
918: of Level-1. For example, requiring that the jet
919: be opposite the photon in $\phi$ and having similar
920: $E_T$. This can be used to select events of
921: a given topology with particularly interesting
922: kinematics, for example. Perhaps more importantly,
923: though, is that this design provides added
924: flexibility for implementing new triggers during the
925: Run~II even if they have not been anticipated before the
926: run begins. This might be in response to better
927: than promised luminosity from the accelerator,
928: or it might be in response to early physics results.
929:
930: Level-2 is where the information from the silicon vertex
931: trigger (SVT) becomes available. Layers of silicon are read out into this
932: trigger, which uses an associative memory and roads
933: provided from the outer tracker to identify silicon
934: tracks. This provides improved momentum resolution,
935: but more importantly, it also provides impact
936: parameter resolution for each track sufficient to
937: identify particles from displaced vertices. Since
938: the vast majority of two track triggers are not
939: from heavy flavor decay, the SVT provides three
940: orders of magnitude rejection.
941: Silicon information doesn't just improve the impact parameter resolution, it also improves
942: the momentum resolution, because the two tend to be highly correlated.
943: The maximum deadtimeless output rate of Level-2 is about 1000~Hz
944: at D\O.
945:
946: By shifting a 3-tube wide window over all the cells in an octant,
947: and looking for wire triplets with a matching scintillator hit, the muon
948: preprocessor first finds track stubs separately in the A-layer and the
949: BC-layer. The track stubs found are reported to an ALPHA preprocessor
950: board that matches track stubs in the A layer with that in the BC-layer,
951: and creates Level-2 objects from matched or unmatched stubs.
952: These Level-2 objects hold the $\phi, \eta$ and $p_T$ of the muon, and are
953: reported to the Level-2 global processor. Upon a Level-2 Accept, the Level-2 objects
954: are sent to Level-3 for more precise muon track reconstruction.
955:
956:
957: \subsection{Trigger Level-3}
958:
959: The third level trigger is often described as an event filter.
960: It is a software-based system characterized by parallel data
961: paths that transfer data from the detector front-end crates to a
962: farm of processors. It reduces the input rate of 1 kHz to an output rate
963: of 50 Hz.
964:
965: D\O's farm of 500 parallel commodity CPU's builds the event into the offline
966: format, runs a modified (for faster execution time) version of
967: the offline reconstruction on the event, and makes a decision to accept
968: or reject the event. If the event is accepted, it is already in or close
969: to the proper format for offline analysis. Additionally,
970: this trigger level can be used to characterize
971: the event and decide whether an event should receive
972: priority in reconstruction. Reconstructing a small
973: fraction (say 1\%) of events in an ``express stream"
974: can be used to provide rapid feedback on the detector's
975: performance and . The overall output rate of
976: Level-3 is about 50~Hz, with some variation depending
977: on luminosity and dataset selection requirements.
978:
979: Running what is effectively the offline reconstruction
980: online also provides an excellent monitor of the health
981: of the experiment. The full offline reconstruction lags
982: a day or two behind the data taking in order to use the
983: final calibration constants, but the Level-3 reconstruction
984: lags only a fraction of a second. Serious problems can
985: therefore be detected before a large amount of data is
986: collected. As an additional benefit, because Level-3
987: looks at the output of Level-2 and offline looks at the
988: output of Level-3, monitoring at Level-3 examines many
989: times more events than offline monitoring, also improving
990: the probability to spot trouble sooner.
991:
992: Using commodity processors has a number of advantages.
993: First, the nature of an event filter naturally lends itself
994: to parallel processing: each CPU processes an entire event,
995: with a supervisor process assigning incoming events to
996: CPUs that finish their events and become ready for new ones.
997: Second, these computers are inexpensive, and getting
998: more so with time, and finally, the system is highly expandable:
999: additional CPU's can be added at a later date, until the
1000: bandwidth into Level-3 becomes the limiting factor.
1001:
1002: The muon Level-3 trigger utilize some aspects of the offline muon
1003: reconstruction. Level-3 muons have more complete information on the
1004: vertex and inner tracking components that will improve
1005: momentum resolution, and has the ability to require that
1006: multiple muons come from the same vertex.
1007: Similar fits are done in Level-1 as in the final offline reconstruction.
1008: Requirements on matching the muon track to the inner tracking
1009: can reduce remnant combinatorics plus punchthroughs.
1010: Level-3 also uses the calorimeter information to reduce combinatorics,
1011: and separate muons into isolated and non-isolated.
1012: Level-3 improves on Level-2's ability to separate muon sources into
1013: prompt, slow, or out-of-time by fitting the available scintillator
1014: hits along a track to the particle's velocity. Level-3 can remove a
1015: cosmic ray muons both by their being out-of-time and by looking for
1016: evidence of a penetrating track on the opposite side of the detector.
1017: Level-3 can also clean up single muon events that Level-1 and
1018: Level-2 identified as dimuons, such as those which pass through
1019: the FAMUS--WAMUS overlap region.
1020:
1021:
1022: %A combinatorial algorithm is used in the Level-3 segment finding, because
1023: %it is faster than the linklist algorithm. The steps are:
1024: %\begin{itemize}
1025: %\item{Segments are first grouped in pairs.}
1026: %\item{Some quantities related to pair of segments are calculated: residual
1027: %in the drift direction and residual in axial direction. }
1028: %\item{The list of segment pairs is sorted in increasing order of residuals
1029: %in the drift direction.}
1030: %\item{Tracks are created using pairs of segments with residuals in the drift and
1031: %axial direction lower than some maximum values. The track momentum is evaluated
1032: %using a parameterization depending on the difference in angles of A and B-C
1033: %segments~\cite{eroshin}.}
1034:
1035: %\begin{itemize}
1036: %\item{for WAMUS}
1037: %$$ p = \frac{0.98}{\theta_{drift}}, $$
1038: %where $\theta_{drift}$ is the difference in angles of A and B-C segments in the drift direction.
1039:
1040: %\item{for FAMUS}
1041: %$$ p = \frac{0.9}{\theta_{\sin}} + \left| {\frac{1.0}{\cos(\theta_A)}} + {\frac{1.1}{\cos(\theta_B)}} \right| * {\rm sign}(\theta_{\sin}), $$
1042: %where $\theta_A$ and $\theta_B$ are the polar angles of A and B-C segments in spherical
1043: %coordinates and where $\theta_{\sin}$ is defined by:
1044: %$\theta_{\sin} = \sin(\theta_B) - \sin(\theta_A)$.
1045:
1046: %\end{itemize}
1047:
1048: %\end{itemize}
1049:
1050:
1051:
1052:
1053: %======================================================
1054: % figure: [hbtp]
1055: %======================================================
1056: \boldmath
1057: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
1058: \subsection{$B$ Triggers with \D0}
1059: \label{detector-btriggers}
1060: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
1061: \unboldmath
1062:
1063: $B$-hadron observability depends strongly on the detector capabilities
1064: to trigger on soft lepton(s) present in semi-leptonic channel or on
1065: $J/\psi$'s produced in $B$ decays. Hadronic $B$ triggers are not considered in
1066: the following.
1067:
1068: The Level-1 muon hardware trigger is based on the combination of low $p_T$
1069: track candidates measured in the CFT, spatially matched with hits in the
1070: scintillator planes and/or drift chambers. Single muon events with
1071: $p_T^{\mu}>4$~GeV/$c$ run prescaled currently, and di-muons with
1072: $p_T^{\mu}>2$~GeV/$c$ are expected to run unprescaled.
1073:
1074: The electron trigger is aimed at soft electron pair detection.
1075: Level-1 candidates are selected separately in EM calorimeter trigger towers
1076: ($\Delta\eta\,=\,\Delta\varphi\,=\,$0.2) with a transverse energy deposit
1077: $E_T>2.0$~GeV, and in the tracking system with a low $p_T$
1078: track coincident with pre-shower cluster. Electron candidates of both systems
1079: are then required to match within a quadrant in $\varphi$
1080: and to have opposite signs. These electron triggers are not used in the following analysis.
1081:
1082: Level-2 triggers include setting of the invariant mass window
1083: and angular cuts in di-lepton channels to select $J/\psi$ decays
1084: and improve background rejection.
1085:
1086: \boldmath
1087: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
1088: \section{Data Acquisition}
1089: \label{detector-daq}
1090: %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%
1091: \unboldmath
1092:
1093: The data flow in trigger Level-3/data acquisition is illustrated in
1094: Fig.~\ref{fig-d0daq}.
1095: Events are reconstructed on the FNAL processor farm system, with
1096: that portion dedicated to \D0 capable of
1097: matching the 50 Hz data acquisition rate. Following reconstruction,
1098: data are stored on a tightly coupled disk and robotic tape system,
1099: and made available for analysis on a centralized analysis processor.
1100:
1101: \begin{figure}[htbp]
1102: \begin{center}
1103: \epsfxsize=3.5 in
1104: \epsfbox{ch3/d0daq.eps}
1105: \end{center}
1106: \caption{Simplified data flow in Level-3/DAQ for D\O ~Run~II.}
1107: \label{fig-d0daq}
1108: \end{figure}
1109:
1110: